Find Jobs
Hire Freelancers

Arduino Teensy IoT Datalogger - merge single electronics projects into a complete Teensy project

£18-36 GBP / hour

クローズ
投稿日: 8年近く前

£18-36 GBP / hour

I have been working to develop an IoT datalogger based on the Arduino platform, I have several separate projects which I would like to merge into a single solution. I intent to use the following components: - OLED - BLE nRF8001 - WiFi ESP8266 - Sound CODEC - SD Card (Data logging and reflash device capabilities) - Sensor I2C board - 2xAnalogue sensors -IR LED Sensor (IR Remote control) -RGB LED stip All the above components work with individually and now I want to pull them together into a single design and looking for someone that can support understanding the hardware and how multiple devices can be connected to the Arduino Teensy 3.2 board. I think the biggest problem will be the OLED, BLE, Sound Codec devices as there use the SPI bus and not sure how to connect multiple devices to the SPI. I would also like to understand if it would be feasibility to refresh the Teensy processor from an image file on the SD card i.e. place a .hex file on the SD card which on start up re-flashes the processor? I have developed the s/w and used the Teensy due to it's increased speed and larger memory compared to the other Arduino platforms. In the presentation you can understand the devices and the connections, the devices can be changed to suit the interface to the Teensy. These components were only selected due to the easy availability from adafruit, eBay etc and happy to exchange them for other components. Therefore, I am looking for the following 1) Understand the components and system 2) Provide a h/w circuit diagram providing a solution to connect up all the above compononens to the Teensy (note: No s/w is required, I can develop that) 3. Understand and provide feedback on the ability to reflash the processor from the SD card and if/what impact that will have on the h/w interface
プロジェクト ID: 10091897

プロジェクトについて

16個の提案
リモートプロジェクト
アクティブ 8年前

お金を稼ぎたいですか?

Freelancerで入札する利点

予算と期間を設定してください
仕事で報酬を得る
提案をご説明ください
登録して仕事に入札するのは無料です
この仕事に16人のフリーランサーが、平均£26 GBP/時間で入札しています
ユーザーアバター
Hi Sir I am an expert electronics engineer with almost 7 years of experience in this field. I have implemented a number of system on arduino and teensy . please have a look at my profile i have gone through the details and I can provide you with the solution you are looking for. i can also provide you complete hardware solution too. Please give me a chance to prove myself. I am waiting for your reply to start the project Regards
£25 GBP 20日以内
4.8 (226 レビュー)
7.9
7.9
ユーザーアバター
A proposal has not yet been provided
£22 GBP 4日以内
4.9 (253 レビュー)
7.5
7.5
ユーザーアバター
Hello, I am Anthony. I am working FULL TIME as freelancer. I have double degrees in Mechatronics and Applied Science fields. I have very good feedbacks on freelancer.com . Please check the link at the end and review my feedbacks. So you can get an idea of my work. I have the capability to guide you until the manufacturing stage. I have many contacts in China and can help you to setup there if you are gonna mass produce your product. I have all the hardware. We can discuss. Contact if you are interested, https://www.freelancer.com/u/Anthony989.html Thank you Anthony
£21 GBP 40日以内
4.8 (63 レビュー)
6.5
6.5
ユーザーアバター
Hi, I can do your project using Arduino Due. I have experience in merging code for electronic modules and build realtime and timesharing system. Best regards, Slavi.
£30 GBP 16日以内
5.0 (18 レビュー)
5.4
5.4
ユーザーアバター
I have 4 years experience in embedded systems. I have completed many projects on arduino base and also iot base device . so I can do your job within a time limit with your satisfaction.
£33 GBP 30日以内
4.8 (8 レビュー)
5.1
5.1
ユーザーアバター
Dear Client, Hope you are doing great. Thanks for the project post and providing an opportunity to bid upon. I am a skilled electronics & PCB consultant with more than 6 years of experience. I have appropriate knowledge and experience in Electronics and PCB designing. I am well versed with digital and analog electronics design. I can work on designs based upon new ideas, reference schematic and redesign/re-engineer circuit based upon actual PCB pics. I have worked upon several projects which includes MCU interfacing, sensor designs, accelerometers and Gyro designs, GPS/GSM designs, RF designs, Bluetooth (BLE2.0, BLE, etc), custom XBEE design, actuator interfacing, amplifier design, audio codec, memory units, USB/FTDI interfacing, battery/power management and many more similar projects. As per my understanding, you have integrated listed module (wi-fi, bluetooth, SD Card, etc) with teensy and now you want them integrated on single PCB hardwired interfaced with Teensy MCU. I have worked upon custom Teensy designs along with similar integration. The power supply, USB connections and other interface will remain on board. SPI bus will support all interface with daisy-chain pattern and interface for the same will provided. I will provide you the complete PCB files, Gerber files, schematic, Bill of materials with supplier codes, etc. Kindly contact for further details and references. Kind regards, Amit
£20 GBP 20日以内
4.6 (4 レビュー)
4.3
4.3
ユーザーアバター
Hi, I have raspberry pi 2 board as of now. let me know your minimum hardware requirement at development site. Thanks Narendra /////////////////////////////////////////////////////////////////////////////////////////////////////////////////
£20 GBP 16日以内
5.0 (3 レビュー)
2.2
2.2
ユーザーアバター
Timothy Woolaver Electrical Engineering Consultant Thank you for your consideration of this proposal. This proposal is for the integration of several Arduino designs in to a single system. About half of my business is turning Arduino projects in to custom PCBs and developing the firmware. I am currently working on a project which has some of the same issues. It has: BLE (nnRF8001 SPI) Camera Arducam Mini (SPI) SD card reader (SPI) Real time Clock (I2C) Mag Card reader (UART) I have it all working but there were a lot of issues along the way. SPI conflicts with the BLE Peripheral library were the biggest issues. I have answers to all of your questions but there is not nearly enough room here to answer them. If you would like to respond to this posting. I can respond with an attached file with the answers and some design examples. I am an Electrical engineer with 25+ years of experience. I have designed and modified the designs of many products and PCBs during my career. Please view my profile to see if my qualifications may meet your needs. Thank you again for your consideration and feel free to contact me with any questions or comments you may have. Thank You Timothy Woolaver Electrical Engineering Consultant One milliamp
£22 GBP 16日以内
3.8 (1 レビュー)
2.7
2.7
ユーザーアバター
With SPI, you should have CS pin to enable/disable the device when the master trying talk to a specific device, the REQ pin should be used for that purpose, I have just done a integration project on ESP8266 wifi based with I2C sensors. I can help you on your project.
£24 GBP 16日以内
0.0 (0 レビュー)
1.4
1.4
ユーザーアバター
Hello There ! I'm excited to let you know that we have worked on Arduino and have expertise in Designing Hardware. We can prepare High Level Diagram and Help you connect all the hardware to Arduino Teensy Board. Normally we can connect many devices to SPI Bus via different addressing . In this case you need to connect many devices to SPI which is possible. Let's connect on chat for more details.
£33 GBP 16日以内
0.0 (0 レビュー)
0.0
0.0

クライアントについて

UNITED KINGDOMのフラグ
Harwich, United Kingdom
5.0
21
お支払い方法確認済み
メンバー登録日:10月 4, 2014

クライアント確認

ありがとうございます!無料クレジットを受け取るリンクをメールしました。
メールを送信中に問題が発生しました。もう一度お試しください。
登録ユーザー 投稿された仕事の合計
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
プレビューを読み込み中
位置情報へのアクセスが許可されました。
あなたのログインセッションの有効期限がきれ、ログアウトされました。もう一度ログインしてください。