Coding required for STM32 MCU

Hi, I have programmed STM32 since 2012. I know both of it's firmware and Hardware issue and familiar with most of it's peripheral. I have use it in various application from Hobbyist,Robotic,Industrial, and Military-aerospace. it's a Powerful MCU. Usually I used STM32CUBEMX as project Generator and System workbench Eclipse as IDE and gcc-Arm-none-eabi as compiller. It's free software that can be used by everyone. What kind of application you want to build? Let's discuss it over chat. Best Regards, Rijal

Hello, I'm interested. Could you provide more info about the project? What exactly do you need to accomplish? I look forward to your reply. Thanks.

I'm an embedded systems engineer with extensive experience with STM32 firmware development in C and C++. I use STM32 devices of different families for most of my work and personal projects. Contact me to discuss details.

Hello there My thesis project was on stm32 MCUs so im completely expert with them. im a master student of electrical engineering. Best regards Mahdi M.

Multiple years of experience with development, and electronics. Experience with the STM32, both "bare-metal" (using TrueStudio/Eclipse/etc.), as well as STM32Arduino. Would love to discuss the details and see how my skills can help you.

Provide more details on the functionality and schematics of the project. Exactly which STM32 micro controller is used.

I've been working with microcontrollers STM32 last 7 years. I have all the hardware to make this job. I have all the qualities that you are looking for. I have a strong belief that I would be able to make this project successful within short time. I will testing completely and write intelligible comments on each program step. And I will answer all your questions. I will give you advice in this area, and after the end of the job, as much as you'll need. I am very interested in the accumulation of work history and regular customers. I have a long term plan to work in here, that’s why I am here with all qualities and experiences. I am here not to cheat you rather help you. The last device which I made this Base Station Controller. 2 uC STM32F373. 74 analog inputs (with a possibility of reassignment of functions). 16 relays. 8 digital inputs. SD memory card, CAN Interface, USB, SPI Interface ,USART Interface, 1-wire Interface, Ethernet(UDP,TCP/IP, FTP), RS-485 Interface ,TFT screen, GSM-modem, heating. 8 user buttons. Analog and digital sensors of temperature/pressure/humidity. Control of single/three-phase mains (definition of frequency, imbalance, health). Control of single/three-phase generator (gas/diesel/petrol). Control wind turbine, solar panel. Measurement 24 battery cells, identify the faulty resistance. Measurement of grounding. Control refueling of fuel tanks (the definition of theft, leakage and other faults). Sending messages about emergency events via GSM, Ethe

Hello, I am good in electronics as well as coding efficienctly . I think i will be able to do the job required. Thanks Mohit

I have done few project with STM32, please share details for better understating of your requirements.

Send me your requirements.

I am expert in STM 32 MCU programming and PCB design. I specialized in development of embedded software and hardware for transport telematics, industrial automation, Internet of Things (IoT) fields. For more details see my profile.

I'm an electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (STM32Fx, NXP, EFM32 SiLabs, but I'm ready to learn new frameworks). I work both single task and multi task environment (FreeRTOS and RTX). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management and for high level/final application. I work also in "C code" commercial boards Arduino/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in C, C++, .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too. I have experience in openCV library for image/video processing.

I'm currently working on STM32 microcontrollers and also i have worked on arduino so many times before. I have implemented canbus communication on STM32 before which is very important and hard system in electronics. I'm sure that i can handle your project in a short time.

More than 5 years experience on stm32 based environment. Please share more details of the project . Price would be as per the project deliverable.