Arduino Class Needed

$250-750 USD

クローズ

投稿日:

約11年前

$250-750 USD

完了時にお支払い

I need a class written for an Arduino. The class could extend the functionality of the One-wire class that already exists. I have an Arduino hooked up to two DS2408 one-wire switches that are connected to a Max 1266 chip. The code needs to read the ADC conversion using two DS2408 chips wired to communicate with the Max1268. I am looking for some one to - write an arduino class that communicates with the two DS2408 chips to a). Handle intialization of the DS/MAX chips b). Initiate a conversion c). Read the 12 bit value from the ADCSkills required:

Arduino

C Programming

C++ Programming

Electrical Engineering

Product Design

プロジェクト ID: 4443799

プロジェクトについて

12個の提案

リモートプロジェクト

アクティブ 11年前

お金を稼ぎたいですか？

メールアドレス

Freelancerで入札する利点

予算と期間を設定してください

仕事で報酬を得る

提案をご説明ください

登録して仕事に入札するのは無料です

この仕事に12人のフリーランサーが、平均$719 USDで入札しています

@MikroStar

hi, i am an electrical engineer and an embedded system designer. i can help you with this project.

$1,256 USD 25日以内

4.9

(41 レビュー)

6.4

@carelle

Hello I can teach you using Team Viewer or Skype.

$660 USD 1日以内

5.0

(36 レビュー)

6.3

@yhaat

Hi, I can do this job.

$735 USD 30日以内

5.0

(24 レビュー)

5.1

@betaenergy

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin

$525 USD 3日以内

4.8

(16 レビュー)

4.9

@nisssal

I'm well experienced in arduino. I can do this for you.

$495 USD 7日以内

5.0

(8 レビュー)

4.4

@theenggprojects

I am ready to start the job

$999 USD 20日以内

4.9

(10 レビュー)

3.8

@michaelroy66

I can start working on your project ASAP.

$440 USD 3日以内

5.0

(1 レビュー)

3.3

@softbike

It's an easy task for us. We have gone through the project requirements and may start working on it immediately. Please check PM for complete details.Thanx.

$770 USD 20日以内

0.0

(0 レビュー)

0.0

@techlotus

It's an easy task for us. We have gone through your requirements and we are ready to start the work immediately on your project. We will send you the complete list of company's projects and portfolio once you reply us back. Also please check the PMB. Thanks.

$770 USD 15日以内

0.0

(0 レビュー)

0.0

@athena0

Interested in this project.

$907 USD 5日以内

0.0

(0 レビュー)

0.0

@getveltrod

Hi, Veltrod Software services is a global software consulting company specialized in providing Mobile applications, Social media frameworks and eCommerce solutions. Leveraging best-in-class people, processes, and technologies, Veltrod provides high-quality software development and BPO services to independent software vendors and enterprises. We are specialized in developing Mobile applications, Search Engine optimizations, Social Network frameworks, Software Testing and ERP applications. We are pleased to take care of this project, if it is offered to us. We assure that we will work towards 100% client satisfaction. Thanks Vinoth

$721 USD 25日以内

0.0

(0 レビュー)

0.0

@XtremeEHS

hi, do you need help?

$330 USD 3日以内

0.0

(0 レビュー)

0.0

@databasesolution

Decades of experience in developing embedded systems in industrial process control and automotive from prototyping to production-ready-design are offered

$550 USD 20日以内