If you want an end to end outsourcing solution for all your projects relating to circuit designing, outsource the work or job at the world's best marketing resource online Freelancer.com and get the work done by the expert circuit designer freelancers. These freelancers work online from all across the world and can be helpful to you and your project. Freelance them the work to be done either on part time or full time basis and be assured of an optimum result. The job sphere may include PCB designing, PCB board circuit debugging, layout, schematic designing, MCS including the software design and the hardware design.

The freelancer circuit designer will be able to work on the PCB print circuit, half finished product design, finished product and also assemble them. Their other work expertise are high speed telecom, RF board, DSP, microcontroller control, signal board, circuit design and assembling, electronic items designing like toy, motor, electronic gifts, main board, security defend, Vidicon, USB, DVD etc. If you are a freelancer having adequate skill and experience in circuit designing, Ethernet, USB, electronics, networking, digital and such related fields, submit your bid in the Freelancer.com and get posted immediately.

Circuit Designersを採用する

絞り込む

私の最近の検索
次の条件で絞り込む:
予算
to
to
to
種類
スキル
言語
    ジョブステータス
    27 仕事が見つかりました。次の価格: USD

    i need html5 expert. and you have to know very well about Bootstrap and CSS 3

    $13 (Avg Bid)
    $13 平均入札額
    2 入札
    ESP-32 signal conditioning. 6 日 left
    認証完了

    To build a board with a signal conditioning for all analog pins of ESP-32 so that a pressure sensor can be measured. The voltage levels are 0.5v-4.5v. Board should accommodate the ESP-32 board connection. Your suggestions are welcomed.

    $194 (Avg Bid)
    $194 平均入札額
    13 入札

    I've an Atemga based micro-controller on an IoT product that I would like to replace with another micro-controller. I attached schematic file. Deliverables for the project: 1) Updated schematics with the new micro-controller (BMD350) 2) Firmware porting from current micro-controller to the new micro-controller

    $196 (Avg Bid)
    $196 平均入札額
    6 入札

    I need circuit designer. Please bid only electronic expert.

    $148 (Avg Bid)
    $148 平均入札額
    25 入札
    ATtiny85 laser project 6 日 left
    認証完了

    I would to develop many projects starting with a simple laser beam receiver by using the ATtiny85. I am using this micro-controller because it is low current consumer. I posted the project attached to this detail assignment.

    $55 (Avg Bid)
    $55 平均入札額
    4 入札

    I've an Atemga based micro-controller on an IoT product that I would like to replace with another micro-controller. I attached schematic file. Deliverables for the project: 1) Updated schematics with the new micro-controller (BMD350) 2) Firmware porting from current micro-controller to the new micro-controller

    $834 (Avg Bid)
    $834 平均入札額
    3 入札

    only operations to perform addition, subtraction, multiplication and division 2. Design of the control unit a. Structure of the control unit (hardwired) b. Design of the control automats use registers for 2 numbers of only 8 bits

    $57 (Avg Bid)
    $57 平均入札額
    6 入札

    this miniproject is only for 2 numbers of 8bits use registers for 2 numbers of only 8 bits only operations to perform addition, subtraction, multiplication and division 1. Design of the processing unit a. Logical diagram of the processing unit b. Algorithm design and manual test of algorithm execution in the processing unit c. Physical design of the processing unit 2. Design of the control un...

    $32 (Avg Bid)
    $32 平均入札額
    2 入札

    Se debe diseñar un procesador basico que realice las 4 operaciones aritmeticas(registro de 8 bits para suma y resta,registro de 16 bits para multiplicacion y division) con unidad de control cableado todo esto en el software proteus. Urgente

    $35 (Avg Bid)
    $35 平均入札額
    1 入札

    This circuit amplifies three input channels consisting of low-current voltage signals that have a low bandwidth (less than 200 Hz). Each channel is pre-amplified according to a fourth circuit input which operates as a voltage control to the pre-amplificiation. Each pre-amplified channel is then fed to a class D amplifier to create a large current version of the input at three respective circuit ...

    $19 / hr (Avg Bid)
    $19 / hr 平均入札額
    7 入札

    Looking for Design Engineer for Isolated DCDC GaN based High Efficiency 120watt Ultra Compact Schematic based on Navitas GaN Power ICs, need to create Schematic and Proto Layout in Altium 40-60V Rectified input, to 20V 6A Clean DC output, regulated down to 0.1V More Details Provided once NDA signed

    $656 (Avg Bid)
    $656 平均入札額
    12 入札
    simple PCB modification (eagle) 5 日 left
    認証完了

    I am looking for someone who can design a simple 2 layer PCB. There is already a shematic and design which can be modified. I can also provide a list of the main components. I will provide shematic and rough geometry of the PCB. Tasks: - Routing - Find and place components - Create new shematic, BOM (xls), Assembly drawing (PDF) and Pick and place files - Create a 3D (STEP) file of the design

    $30 (Avg Bid)
    $30 平均入札額
    34 入札

    I need detailed design & engineering support for development of solar, wind, diesel generator, battery bank & grid connected hybrid inverter of 3 kVA rating. The scope includes detailed engineering, sizing calculation, PCB design, firmware development, logic development, micro controller code for the hybrid inverter with battery charge controller and synchronization unit. Hardware work is ...

    $149 (Avg Bid)
    $149 平均入札額
    4 入札

    I am working on a project that will allow the use of one driver board (small) to power two 1 MHz piezoelectric discs. The prospective engineer should be able to create or edit a schematic diagram and design a PCB layout that will allow this. It is acceptable to find an inexpensive and easily obtainable driver board on the retail market that can complete the mentioned task.

    $196 (Avg Bid)
    $196 平均入札額
    14 入札

    very basic electronic circuit assembly suit someone working from home. sheffield / derbyshire area

    $566 (Avg Bid)
    $566 平均入札額
    22 入札

    We need Custom PCB with esp32, ethernet port, 485 comunication, 4x fet output. Runs on 5V.

    $199 (Avg Bid)
    $199 平均入札額
    21 入札

    The deliverable is to get current print head working. The perfect developer with have the ability to review / create schematic design, PCB design, BOM, Gerber files and 3D model file for the printhead custom board. You will be required to sign a non disclosure agreement. Would you consider yourself an expert with Epson printheads. If not what is your level of expertise? Do you know anything abo...

    $170 (Avg Bid)
    $170 平均入札額
    6 入札

    I am looking for Haddware and firmware development for building an AC Energymetering circuit using M90E26 ( Single phase enegry Metering IC). I would be looking for Hardware circuit design + PCB layout + Required Firmware. ( complete solution and working hardware 1 unit)

    $110 (Avg Bid)
    $110 平均入札額
    7 入札
    I need a schematic expert. 2 日 left
    認証完了

    Hello, I have a hardware design project. I need to start from schematic design. The candidate should be strong at skills for hardware design. The schematic has reference design and need to add several chips on it. I will give details to the most powerful candidate. Someone who has experience in Qualcomm SoC is a plus. Please write down "Qualcomm" at the first line of your proposal. Other...

    $106 (Avg Bid)
    $106 平均入札額
    7 入札
    Flow sensor -- 2 2 日 left
    認証完了

    Design and build a working prototype for an accurate non intrusive 'clamp-on' flow sensor for use on liquid and gas pipes. ultrasonic/Doppler/magnetic/piezoelectric crystal/ time based- For use in Raspberry PI project.

    $237 (Avg Bid)
    $237 平均入札額
    7 入札

    I need to hire someone to draw out my electrical setup for my warehouse which I want to turn into a free weight gym. I am told I need an Electrical Engineer to draw out the electrical lines, plugs, etc...

    $171 (Avg Bid)
    $171 平均入札額
    9 入札

    PCB DESIGN FOR 15kW DC-EV Charger consist of the following parts: 1- PFC 2- HV DC-DC BOOST CONVERTER

    $1336 (Avg Bid)
    $1336 平均入札額
    13 入札

    Requiero que me realizen el diseño de un procesador basico que realize las operaciones aritmeticas basicas (suma,resta,division,multiplicacion) con el software de "Proteus 8.8".

    $28 (Avg Bid)
    $28 平均入札額
    4 入札

    Looking for a freelance electrical engineer in Southern California (Orange County) to design, build and troubleshoot custom electronics and put together instrumentation for test and measurement for various projects. Would require visits to our site to discuss details with our engineers. Mixed signal applications and some embedded computing skills required. Experience with high frequency circuits a...

    $37 / hr (Avg Bid)
    $37 / hr 平均入札額
    8 入札

    Goal - Professional Electrical Wiring Diagram Timeline - 2-3 Weeks Details - [ログインしてURLを表示] Wiring Diagram for a machine with PLC's, MCB's, Contactors, Camera, Ethernet Device,etc 2. Must be able to export in professional pdf format with inter- connections of wiring diagram 3. Must explain every cable definition and wire connection 4. If done in EPlan software, will be the best and favo...

    $31 (Avg Bid)
    $31 平均入札額
    22 入札
    rfid engineer 9 時間 left

    rfid low voltage project to detect close objects with rfid tag on it.

    $466 (Avg Bid)
    $466 平均入札額
    26 入札

    21,600 volt line with wind, solar and gas generation with grid tie

    $2723 (Avg Bid)
    $2723 平均入札額
    17 入札